Triplett TEV500 Pro Electric Vehicle Charger Test Kit

Triplett TEV500 Pro Electric Vehicle Charger Test Kit
Triplett TEV500 Pro Electric Vehicle Charger Test Kit
Triplett TEV500 Pro Electric Vehicle Charger Test Kit

Triplett TEV500 Pro Electric Vehicle Charger Test Kit

P/N: 43329

The Triplett Model TEV500 PRO Electric Vehicle Charger Test Kit tests charging stations using basic & advanced diagnostics.

Triplett WireMaster Mapper 8-Way Wire & Cable Mapping Kit

PE Pre-Test checks the PE conductor for the possible presence of dangerous voltage against earth. With the CP (Control Pilot) State rotary switch selector various vehicle states can be simulated. You can use the CP Signal output terminals to connect your oscilloscope to check the waveform and amplitude of the CP signal.

Learn more

$560.00

Already In Wishlist Add to Wishlist Add to WishlistAlready In Wishlist
Add to Wishlist
Categories: ,

CP Error “E” simulates the behavior of the station when there is an established short circuit between CP and PE. PE Error (Earth Fault) simulates interruption of the PE conductor. When the CCID TRIP Test Button is pressed, a connection between L1 and PE is established and CCID from the station should abort charging process. A phase indicator LED will illuminate when phase voltage on L1 is present at the charging connector.

The Measuring Terminal Outputs L1, L2(N), PE and PP are directly connected to the L1, L2(N), PE and PP conductors of the tested charging station. You can use your digital multimeter for quickly viewing voltage readings on these lines. SAE J1772 complies with North American standards. Includes (1) IEC62196-2 Type 1 female to male adaptor/converter and pouch case.

  • Test charging stations for both basic & advanced diagnostic requirements
  • PE Pre-Test: Allows testing the PE conductor for possible presence of dangerous voltage against earth
  • Control Pilot (CP) State (Vehicle Simulation): With the CP State rotary switch selector various vehicle states can be simulated
  • CP Signal State Output: For use with an oscilloscope to check the waveform and amplitude of the CP signals
  • CP Error “E” simulation: Simulate the behavior of the station when there is an established short circuit between CP and PE
  • PE Error (Earth Fault) simulation: Simulates interruption of the PE conductor
  • CCID TRIP Test Button: When pressed a connection between L1 and PE is established and CCID from the station should abort charging process
  • Phase indicator LED: When phase voltage on L1 is present at the charging connector, the LED indicator will illuminate
  • Measuring Terminal Outputs L1, L2(N), PE and PP: Directly connected to L1, L2(N), PE and PP conductors of the tested charging station. It is allowed to use these for measuring purposes only and can be used with any Digital Multimeter for viewing voltage readings
  • SAE J1772 -Complies with North American standards
  • Includes: (1) IEC62196-2 Type 1 female to male adaptor/converter and pouch case

Specs & Features

Highlights

  • LAN / Network Cable Tests – Cable Diagram Wire Map, Pass/Fail, Delay, Skew, Ohms
  • Speed Detection – Displays the 10/100/1000 capabilities of any active port (computer, switch, VoIP, access point).
  • Cable Length Test – Indicates cable length, distance to open or short.
  • Return Loss Quality Tests – Tests for load mismatches that affect the wire’s power and data transfer capability.
  • PoE Testing – Detect PoE Voltage and display its amplitude and location on the cable (midspan, endspan or both).
  • Store and Print up to 250 Reports on all cable types.
  • Wall Jack ID – Smart Remotes allow Test & ID in one pass, RJ45 & Coax.
  • Speaker Popper – Locate and identify speakers by audibly “popping” them.
  • Port Blink Cable Detection – Locate cable connection to a switch port by blinking the switch’s Link LED.
  • Test RJ45, Coax and RJ11 Cables for faults.
  • Tone Generator – Send a tone from one end and detect it on the far end (tone probe required).
  • Alert LEDs (Links and Volts) – Two LED’s quickly alert you to an active switch connection or voltage on the line.
  • CCTV / Vpp (Peak to peak voltage) – CCTV systems require a minimum of 1 Vpp to DVR. Measure and display the Vpp of video signals.
  • Phone – Detect central office telephone connections. Display voltage and cable location (up to 4 phones).
  • Loaded Battery Test – Reliably test alarm and security system backup batteries with a load test.
  • Store and print with included LVPRO Manager Software
  • Includes 8 Smart Remotes for Cable ID and multiple drop testing.
Weight 2 lbs

  • TEV500 Pro EVCharger
  • (1) IEC62196-2 Type 1 female to male adaptor/converter
  • Pouch case