Triplett TEV200 EV Probe Kit

Name: Triplett TEV200 EV Probe Kit
SKU: 43331
Availability: InStock

Triplett TEV200 EV Probe Kit

P/N: 43331

The Triplett Model TEV200 Electric Vehicle Probe Kit plugs directly into your Digital Multimeter, Clamp Meter or Multifunction Tester (MFT) and allows you to perform typical measurements: voltage, frequency, phase indication, phase sequence, various RCD tests, insulation resistance, low ohm measurements, line and loop impedances (if supported by the measuring input device).

It easily connects by wire (Standard Male Banana Type) between the EVSE charging point (Type-2 connector) and the measurement inputs of the DMM, Clamp or MFT.

Learn more

SKU: 43331

$240.00

Categories: EV Test Equipment, Triplett Test Equipment

All wires of the charging connector are available: L1, L2, L3, N, PE, CP and PP. The built-In Control Pilot (CP) State (Vehicle Simulation Switch) can simulate vehicle states with different resistances connected between CP and PE conductors. You can use the CP Signal output terminals to connect your oscilloscope to check the waveform and amplitude of the CP signal. CP Error “E” simulates the behavior of the station when there is an established short circuit between CP and PE. The Probe Kit complies with EMC Directive (2014/30/EU), the Low Voltage Directive (2014/35/EU), and EN61010-1 standards. Plugs directly into your Digital Multimeter (DMM), Clamp Meter or Multifunction Tester (MFT)

Simply connects by wire (Standard Male Banana Type) between the EVSE charging point (Type-2 connector) and the measurement inputs of the DMM, Clamp or MFT. All wires of the charging connector are available: L1, L2, L3, N, PE, CP and PP
Allows you to perform typical measurements: voltage, frequency, phase indication, phase sequence, various RCD tests, insulation resistance, low ohm measurements, line and loop impedances (If supported by the measuring input device)
Built-In Control Pilot (CP) State (Vehicle Simulation Switch) – Different vehicle states can be simulated: Vehicle states are simulated with different resistances connected between CP and PE conductors
CP Signal output terminals – Use an oscilloscope to check the waveform and amplitude of the CP signal
CP Error “E” simulation: Simulate the behavior of the station when there is an established short circuit between CP and PE
Complies with EMC Directive (2014/30/EU), the Low Voltage Directive (2014/35/EU), and EN61010-1 standards
Includes: (1) IEC62196-2 Type 1 female to male adaptor/converter and pouch case2196-2 Type 1 female to male adaptor/converter and pouch case

Specs & Features

Highlights

LAN / Network Cable Tests – Cable Diagram Wire Map, Pass/Fail, Delay, Skew, Ohms
Speed Detection – Displays the 10/100/1000 capabilities of any active port (computer, switch, VoIP, access point).
Cable Length Test – Indicates cable length, distance to open or short.
Return Loss Quality Tests – Tests for load mismatches that affect the wire’s power and data transfer capability.
PoE Testing – Detect PoE Voltage and display its amplitude and location on the cable (midspan, endspan or both).
Store and Print up to 250 Reports on all cable types.
Wall Jack ID – Smart Remotes allow Test & ID in one pass, RJ45 & Coax.
Speaker Popper – Locate and identify speakers by audibly “popping” them.
Port Blink Cable Detection – Locate cable connection to a switch port by blinking the switch’s Link LED.
Test RJ45, Coax and RJ11 Cables for faults.
Tone Generator – Send a tone from one end and detect it on the far end (tone probe required).
Alert LEDs (Links and Volts) – Two LED’s quickly alert you to an active switch connection or voltage on the line.
CCTV / Vpp (Peak to peak voltage) – CCTV systems require a minimum of 1 Vpp to DVR. Measure and display the Vpp of video signals.
Phone – Detect central office telephone connections. Display voltage and cable location (up to 4 phones).
Loaded Battery Test – Reliably test alarm and security system backup batteries with a load test.
Store and print with included LVPRO Manager Software
Includes 8 Smart Remotes for Cable ID and multiple drop testing.

Weight	2 lbs

TEV200 EV Probe
(1) IEC62196-2 Type 1 female to male adaptor/converter
Pouch case

All hand tools come with a lifetime warranty through Tecra Tools. Cases follow the manufacturer’s warranty and are handled via Tecra Tools. Warranties for test equipment and power tools must be addressed directly with the manufacturer for repair or replacement. Please see our full Warranty Policy.

All returns must be pre-authorized and clearly marked "returned goods" and returned within 10 days (customer is responsible for all return shipping costs). Custom Cases, Custom Kits, Special Order Items (SPC's), Replacement Parts, Clearance/Sale/Promo Code Items and Test Equipment are Non Exchangeable, Non Returnable or Non Refundable. Exceptions may apply but not without prior authorization from Tecra Tools. Please see our full Return Policy.

Pricing Policy
All prices listed on Tecra Tools' website reflect the most accurate and up-to-date information available. If an "original price" or "discounted price" is displayed, the original price represents the price at which the product was offered in the past for a reasonably substantial period of time. Any "sale" or "discount" applies for a limited time as specified on the product page. Tecra Tools reserves the right to modify or update pricing without notice. For further details about pricing, see Terms & Conditions or please contact us at 1-800-284-0808 or info@tecratools.com.

Shipping Policy
Our website does not reflect live inventory, except for a select number of items. In stock products will ship within 72 hours. If your order is in stock, but received after 2 PM MST, your order will be processed and shipped on the next business day. If you are needing a product by a certain deadline, please reach out to us at info@tecratools.com or call 303-338-9224 and we can provide you more information. See full shipping policy at Term & Conditions.

Customer Support
For questions or concerns, please contact us at: