Net Chaser Ethernet Certifier and Network Tester

Thumbnails here

Net Chaser Ethernet Certifier and Network Tester
Net Chaser Ethernet Certifier and Network Tester

Net Chaser Ethernet Speed Certifier Kit with Active Remote

P/N: 37900

Isn’t it time to put affordable 21st Century Network speed certification in the palm of your hand?

Platinum Tools

Your complete solution to test and speed certify your LAN is here! The Net Chaser Ethernet Speed Certifier performs comprehensive speed tests to certify your network up to 1 Gb/s speeds and document compliance with critical IEEE 802.3 and TIA568A/B standards. This tester checks for network noise or misconfiguration, and cabling faults to ensure cables can support the speeds your active equipment requires.

Learn more

$2,558.00

Categories: , , ,

It’s advanced Ethernet discovery capabilities and diagnostics allow you to troubleshoot, record and report any network issues and obtain a clear picture of the network layout and interfaces between active components, like servers, switches and routers. All the data is collected and stored in the NetChaser for pass/fail speed validation, certification and reporting.

  • Full battery of Gigabit Ethernet Speed certification and performance testing for IEEE 802.3 compliance
  • Bit Error Rate Testing (BER) using the included Active Remote – Sends data packets at defined data rates to check for errors at maximum throughput
  • Signal-to-noise ratio (SNR) – Checks cable runs for error-causing noise
  • Skew measurements – Reporting on signal time transmission delays between pairs
  • Cable continuity tests for opens, shorts, miswires, split pairs, reversals and high-resistance faults
  • Supports IPV4 and IPV6 protocols
  • Traceroute function displays the path of Internet packets to reach a specified destination IP address
  • DHCP connectivity and DNS Verification
  • Ping specific IP addresses or URLs (Ping up to 10 addresses simultaneously)
  • VLAN discovery
  • Discover network devices using Cisco Discovery Protocol (CDP) or Link Layer Discovery Protocol (LLDP)
  • Full color graphical wire-mapping with Pass or Fail Message
  • Tests CAT3/CAT5e/CAT6/6a Ethernet cable configuration and verifies connectivity
  • Displays cable length measurement for each pair in feet or meters using TDR technology
  • Detects presence of PoE and class of PoE per IEEE 802.3af/at with load test for voltage drop
  • Detects and reports current link speed and link capabilities for active Ethernet drops up to 1 Gbps
  • Link light to identify location on a hub/switch/router port
  • Generates selectable tones on specified pins for use with tone tracers
  • Supports up to 8 testing & ID remotes for network & telephone cables
  • Supports up to 20 network & coax ID – only mapping remotes
  • View and save hundreds of cable test results
  • Ability to define cable name, save cable tests and print ALL results (both cable tests & network tests)
  • Made in the USA

Additional information

Weight 11 lbs

  • Full battery of Gigabit Ethernet Speed certification and performance testing for IEEE 802.3 compliance
  • Bit Error Rate Testing (BER) using the included Active Remote - Sends data packets at defined data rates to check for errors at maximum throughput
  • Signal-to-noise ratio (SNR) - Checks cable runs for error-causing noise
  • Skew measurements - Reporting on signal time transmission delays between pairs
  • Cable continuity tests for opens, shorts, miswires, split pairs, reversals and high-resistance faults
  • Supports IPV4 and IPV6 protocols
  • Traceroute function displays the path of Internet packets to reach a specified destination IP address
  • DHCP connectivity and DNS Verification
  • Ping specific IP addresses or URLs (Ping up to 10 addresses simultaneously)
  • VLAN discovery
  • Discover network devices using Cisco Discovery Protocol (CDP) or Link Layer Discovery Protocol (LLDP)
  • Full color graphical wire-mapping with Pass or Fail Message
  • Tests CAT3/CAT5e/CAT6/6a Ethernet cable configuration and verifies connectivity
  • Displays cable length measurement for each pair in feet or meters using TDR technology
  • Detects presence of PoE and class of PoE per IEEE 802.3af/at with load test for voltage drop
  • Detects and reports current link speed and link capabilities for active Ethernet drops up to 1 Gbps
  • Link light to identify location on a hub/switch/router port
  • Generates selectable tones on specified pins for use with tone tracers
  • Supports up to 8 testing & ID remotes for network & telephone cables
  • Supports up to 20 network & coax ID – only mapping remotes
  • View and save hundreds of cable test results
  • Ability to define cable name, save cable tests and print ALL results (both cable tests & network tests)
  • Made in the USA

Reviews

There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.